Product Description
Barnes 6ESCDK10066 Dry Run Chopper Pump - 10 HP, 208V 3-Phase
The Barnes 6ESCDK10066 is a 10 HP submersible chopper pump from the Dry Run Submersible Motors / 6ESCDK line by Crane Pumps & Systems, 208/3 volts/phase. Discharge: 6", 125 lb. Horizontal flange slotted to accommodate 150mm ISO flanges. Crane does not publish a separate part number for this configuration, so order by model number. Call for pricing (416) 236-2338 or email sales@bramhambros.com.
Model Data
| Pump Model Number - Voltage/Phase | 6ESCDK10066 - 208/3 |
|---|---|
| Driver Frame | E28 |
| Voltage / Phase | 208/3 |
| RPM (Nominal) | 1150 |
| NEMA Start Code | H |
| Hz | 60 |
| Full Load Amps | 27.5 |
| Locked Rotor Amps | 188.0 |
| Cord Part Number | 125496 |
| Cord Size | 12/4 - 18/4 |
| Power Factor 100% Load | 82.6 |
| Power Factor 75% Load | 78.1 |
| Power Factor 50% Load | 68.7 |
| Motor Efficiency 100% Load | 91.4 |
| Motor Efficiency 75% Load | 92.0 |
| Motor Efficiency 50% Load | 91.5 |
| Weight (lbs) | 811 |
| Working Pressure (Psi) | 38 |
Performance Curve
Standard Impeller Sizes
| Pump HP | Impeller Dia mm (in.) |
|---|---|
| 40 | 370 (14.57) |
| 30 | 345 (13.58) |
| 25 | 345 (13.58) |
| 20 | 325 (12.80) |
| 15 | 290 (11.42) |
| 10 | 250 (9.84) |
| 7.5 | 235 (9.25) |
Dimensions
All dimensions are in inches (mm).
Specifications
| Discharge | 6", 125 lb. Horizontal flange slotted to accommodate 150mm ISO flanges |
|---|---|
| Suction | 8", 125lb ANSI flange |
| Striker Plate | 440C Stainless steel heat treated to 53-60 HRC hole pattern to accommodate 8" 125# flange |
| Speed | 1150 RPM |
| Impeller | Design: Enclosed Dual-Vane, with pump out vanes on back side. Dynamically balanced ISO G6.3. Material: Ductile iron ASTM A-536, 65-45-12 |
| Cord Entry | Custom Molded quick connected for sealing and strain relief (E21 & E28 FRAME ONLY) |
| Maximum Liquid Temperature | 104°F (40°C) Continuous |
| Volute | Cast iron ASTM A-48, Class 30 |
| Wear Ring | C954 Lead-free bronze |
| Slicing Blade | 440C Stainless steel heat treated to 53-60 HRC |
| O-Rings | Buna-N |
| Hardware | 300 Series stainless steel |
| Motor | Design: NEMA B three phase torque curve, air-filled, squirrel cage induction, inverter duty rated per NEMA MG1 Insulation: Class H Efficiency: IE3 Voltage: 208, 230, 460, 575 (±10% voltage variation) Service Factor: 1.15 |
| Shaft | 416 Stainless steel |
| Starts Per Hour | E21 and E28 Frame: 30 Starts per Hour, evenly spaced E32 and E36 Frame: 15 Starts per Hour, evenly spaced |
| Cooling System | Closed loop cooling system Cooling Jacket: - E21, E28, and E32 Frame: 300 Series stainless steel - E36 Frame: Integral cast iron jacket ASTM A-48, Class 35B |
| Submergence | Max depth 66ft (20m) |
| Motor Housing | Cast iron ASTM A-48, Class 35B |
| Seal Bracket | Cast iron ASTM A-48, Class 35B |
| Lower Bearing | Design: Double Row, Ball, permanently Grease Lubricated Load: Radial & Thrust |
| Upper Bearing | Design: Single Row, Ball, permanently Grease Lubricated Load: Radial |
| Bearing Bracket Assembly | Cast iron ASTM A-48, Class 35B |
| Hardware And Lifting Bail | 300 Series stainless steel |
| Seal | Design: Tandem mechanical Material: - Inboard: Carbon rotating face, silicon carbide stationary face - Outboard: Silicon carbide rotating face, silicon carbide stationary face - Elastomer: Buna-N - Hardware: 300 Series stainless steel |
| Power Cord | CSA certified submersible power cable - ordered separately |
| Motor End Coating System | Resicoat® R4 Powder Coat Epoxy TEST BLUE |
| Pump End Coating System | Axalta Corlar® Amidoamine Epoxy |
| Optional Equipment | White iron impeller, impeller trims, impeller types, cord length, seal options, certified testing |
| Markings | CSA |
| Moisture Sensor | Normally open (N/O) float sensor with resistor, located in seal chamber, requires relay in control panel |
| Temperature Sensor | Three phase - Three normally closed (N/C) thermal sensors, one per phase, embedded in stator windings, to be wired in series with control circuit. |
| Overload Protection | Three phase - must be included in the control panel |
Notes
- Moisture and Temperature sensor leads are integral to power cord.
- Pump rated for operation at ± 10% voltage at motor.
- ▲ Cord Suffix: XC - 30 Feet, XF - 50 Feet, XJ - 75 Feet, or XL - 100 Feet.
- ▲ Cord sold separately.
- * Tri-voltage pumps (i.e. 208-230/460V) are operable at 208V, but will not meet IE3 efficiency. A true 208V, single voltage pump must be ordered to obtain an IE3 rating.
- NOTE: Envie3 Dry Run Submersible motors tested per CSA C390/IEEE-112. Efficiency levels are comparable to that of motors meeting the IEC60034-30 standard.
Documents
Optional Accessories
Break Away Fitting, Metal Stand, Flygt Adapter, Level Controls, Conditioning Stand, Concrete Stand, Horizontal Cart System, Fixed Bracket, Cable Rack, Pump Monitor Relay, Videos. Ask us about matching accessories for this pump.
Call for pricing (416) 236-2338 or email sales@bramhambros.com
Product Videos
Custom Field
Brand Barnes
Product Line Chopper Pumps
Series Dry Run Submersible Motors / 6ESCDK
Model 6ESCDK10066
Part Number Order by model number
Horsepower 10 HP
Voltage / Phase 208/3
Hz 60
RPM 1150
Full Load Amps 27.5
Driver Frame E28
Discharge 6", 125 lb. Horizontal flange slotted to accommodate 150mm ISO flanges
